Author [ES] [CA] [PL] [PT] [IT] [DE] [FR] [NL] [DK] [NO] [GR] [TR] Topic: Stator Suppliers  (Read 836 times)

0 Members and 1 Guest are viewing this topic.

Offline vinciebhoy

  • CBF Member
  • **
  • Posts: 27
  • Bike: CBF1000A-8
  • City / Town: Paisley
  • Country: Scotland
Stator Suppliers
« on: 08 September, 2019, 10:45:32 PM »
Hi, I am now a member of the Burnt out Stator club and I am looking for an up to date list of the better suppliers of Stators.
I fitted a volt meter in march this year as I wanted an early warning of a stator failure.
On the way back from a 221 mile ride out on Saturday ( 5 miles from home) the Volt meter showed 12.1 volts and on testing today I have found that I need to replace the Stator.

 :028:
« Last Edit: 08 September, 2019, 10:47:35 PM by vinciebhoy »

Offline Piper

  • CBF Master
  • ****
  • Posts: 604
  • City / Town: NW Kent
Re: Stator Suppliers
« Reply #1 on: 09 September, 2019, 08:25:29 AM »
Loads of threads on this site for stators. Here for example

https://www.cbf1000.com/index.php?topic=18550.0

Good luck.

Offline Art

  • CBF Master
  • ****
  • Posts: 367
  • Bike: 2006 CBF1000 A-6
  • City / Town: London
  • Country: UK
Re: Stator Suppliers
« Reply #2 on: 09 September, 2019, 10:35:05 AM »
When my stator failed after a very reasonable 11 years of excellent service I replaced it for a £95 (now £110) Electrosport direct fit stator from M&P. Link here https://www.mandp.co.uk/products/honda-cbf1000-06-12-generator-stator-electrosport-677550

That was 2 years ago, if it failed again now or, if there had been London stock 2 years ago, I'd have been tempted with what appears to be London stock of a Chinese direct fit stator at £41.79 delivered. Link here https://www.ebay.co.uk/itm/Magneto-Generator-Stator-Coil-For-Honda-CBF1000-sc58-2006-2011-GB/352724338867

Not doubting your charging system diagnosis and assuming you got less than the expected 14.8v at 5,000 RPM. However my goto friend when suspecting a charging system fault is Electrosport’s generic fault finding flow chart for motorcycle charging systems, link here https://cdn.shopify.com/s/files/1/1091/5694/files/fault-finding-diagram.pdf?235929069374954073

Offline vinciebhoy

  • CBF Member
  • **
  • Posts: 27
  • Bike: CBF1000A-8
  • City / Town: Paisley
  • Country: Scotland
Re: Stator Suppliers
« Reply #3 on: 09 September, 2019, 12:26:40 PM »
Thanks for the quick reply's
The regulator tested OK, but when I done a resistance check on the stator I got 2.3 ohms between windings and the same when I test each to ground, on the attached photo you can see top right looks a tad too black!!
I will probably go for the electrosport stator.

Cheers

 :002:

Offline Art

  • CBF Master
  • ****
  • Posts: 367
  • Bike: 2006 CBF1000 A-6
  • City / Town: London
  • Country: UK
Re: Stator Suppliers
« Reply #4 on: 09 September, 2019, 02:19:23 PM »
Sounds as if you tested it all in a 'proper job' style. At 2.3 ohms across the windings the stator wouldn't have completely failed but will be in need of replacement since that failure is waiting to happen any time soon. No photo attached but certainly if you have blackened windings that's the writing on the wall. Sounds as if you got the warning just in time. I've always resisted the need for an onboard voltage meter, maybe I should re-consider. It would have to be an actual voltage readout rather than one of those traffic light gadgets that are forever flickering between green, amber and red without actually telling you what the voltage is.

Offline vinciebhoy

  • CBF Member
  • **
  • Posts: 27
  • Bike: CBF1000A-8
  • City / Town: Paisley
  • Country: Scotland
Re: Stator Suppliers
« Reply #5 on: 09 September, 2019, 06:05:30 PM »
Yeh the 2.3 ohms is the total resistance of what each segment should be and the reading to earth shows that the burnt out segment is probably shorting to earth.

Picture on original post.

Offline Art

  • CBF Master
  • ****
  • Posts: 367
  • Bike: 2006 CBF1000 A-6
  • City / Town: London
  • Country: UK
Re: Stator Suppliers
« Reply #6 on: 09 September, 2019, 06:33:11 PM »
That'll be back on the road in no time.

Offline catford lad

  • CBF Member
  • **
  • Posts: 16
  • Bike: Honda cbf1000A6
  • City / Town: London
  • Country: England
Re: Stator Suppliers
« Reply #7 on: 11 September, 2019, 04:20:43 PM »
I used a company called Electrex. They manufacture in house and also do a reg/rec. Good service.

Offline raYzerman

  • CBF Member
  • **
  • Posts: 58
  • Bike: FJR1300A CBF1000
  • City / Town: Millgrove, ON
  • Country: Canada
Re: Stator Suppliers
« Reply #8 on: 11 September, 2019, 06:30:39 PM »
I bought a spare stator from RM Stator, a reputable company here... the box is labelled Made In China.  If I were getting a spare again, I'd just get one from China much cheaper.

Offline VanquishedWombat

  • CBF Member
  • **
  • Posts: 15
  • Bike: CBF1000FA ABS
  • City / Town: Winchester
  • Country: UK
Re: Stator Suppliers
« Reply #9 on: 11 September, 2019, 07:58:35 PM »
I have a MkI and am pondering fitting a volt meter for same purpose as you. As I'm not sure I'll be able to remember the meanings of the traffic light variety I was wondering what meter you fitted and if you had a pic of it in situ, was it easy to fit, etc ?

VW.

 


diverse-leafy